Job Posting End Date

07-13-2025

Please note the job posting will close on the day before the posting end date

Job Summary

Perform work associated with the installation, operation, testing and maintenance of fundamental protection and control devices and related equipment under general supervision. Such devices and equipment includes but is not limited to digital relays, electromechanical relays, intelligent electronic devices, Station Disturbance Recorders (SDR), digital fault recorders (DFR), event recorders, RTU's and station SCADA systems, statistical load metering, telemetering and transducers. Additionally, install, maintain and operate all power line carriers (PLC), tone, pilot wire, fiber and associated P&C communications equipment. Respond to emergency call-outs and coordinate prompt restoration of service to customers as required. This list is not intended to limit assignment of work or the degree of supervision under all operating conditions. Employee may perform miscellaneous, related, and incidental work in addition to that specifically outlined below.

Job Description

Please Note this job is posted in a range from P&C Technologist Assoc – P&C Technologist Senior

A successful candidate should live within 45 minutes of the Robert E Matthews Service Center (12333 Kevin Ave, Ashland KY 41102) Or the Pikeville Transmission Service Center (6809 North Mayo Trail, Pikeville KY 41501)

P&C Field Technologist Assoc:

ESSENTIAL JOB FUNCTIONS:

1. Test fundamental protection & control devices and equipment periodically and as required.

2. Calibrate fundamental protection & control devices and equipment on a pre-established schedule and as required.

3. Assist with switching at all voltage levels under the direction of the proper Dispatching Authority.

4. Maintain test equipment in good working order.

5. Maintain accurate records, reports and drawings as required.

6. Operate a computer device to test, calibrate, and retrieve data from protection & control devices.

7. Assist in the installation, maintenance, and operation of all relays, power line carrier sets, station SCADA, and associated communications equipment or cables as assigned.

8. Troubleshoot and repair fundamental electromechanical relays.

9. Troubleshoot and repair microprocessor based relays at the card level, such as replacing power supplies, communications cards, I/O cards, etc.

10. Assist with the diagnosis of equipment failures, protection mis-operations, and assist with corrective action to perform repairs and prevent recurrence.

11. Ensure the circuitry, installation and operation of equipment is correct prior to placing equipment in service. Read electrical schematics and determine that the physical installation at the site is electrically equivalent to the schematic. Record test readings and results and determine they are within acceptable specifications and thus the physical installation will perform as per the design.

12. Basic fault analysis: obtain oscillography data to determine if the protective devices operated as per their issued relay settings.

13. Assisting a team in the installation, testing, and commissioning of new P&C systems for capital construction projects. Assist the on-site technical lead with directing the activities of contract wireman and the activities of other P&C field personnel assigned to their project.

14. Assist a trip testing team.

MINIMUM REQUIREMENTS:

Education: Bachelor's degree in engineering in a program accredited by the Engineering Accreditation Commission of the Accreditation Board for Engineering and Technology (ABET) or a Bachelor's degree in engineering technology in a program accredited by the Technology Accreditation Commission of the Accreditation Board for Engineering and Technology (ABET).

Experience: This is an entry level position for new graduates with a Bachelor's degree.Must successfully complete the Physical Abilities Test (PAT).Must be able to distinguish colors on a standard color blindness test.

OTHER REQUIREMENTS:

1. Working knowledge of current, potential, closing and trip circuits.

2. Working knowledge of material such as cable, lugs, and wire as applied to protective relay and control circuits.

3. Working knowledge of assembly, anchoring, and interchangeability of the various switchboard panel-support and through systems.

4. Must have the ability to read, understand, and correct electrical prints and diagrams and the ability to use hand tools.

5. Must demonstrate the ability to perform duties in an alert, safe, and business-like manner and the ability to deal with customers and other employees in a courteous and professional manner.

6. Ability to interpret, analyze and transmit facts graphically, orally, and in writing clearly and precisely.

7. Must possess and maintain a valid state driver’s license and must meet all vehicle operation requirements as designated by federal and/or state law.

8. Considerable travel and overtime may be required to complete work assignments.

COMPETENCIESTECHNICAL PROFICIENCY: Possesses technical to entry level knowledge acquired from a Bachelor’s Degree in an ABET accredited engineering technology program; demonstrates the ability to perform with proper guidance special technical functions required in the relevant area of assignment; gains familiarity with standards, codes, and regulations relevant to the area of assignment; gains familiarity with pertinent equipment, materials, systems, and business processes; assists higher level employees in handling well defined portions of routine problems;

PLANNING AND ORGANIZATION ABILITY: Maintains required records to support assignments and prepares special reports for tests, equipment performance, projects and other reports as assigned; plans work in accordance with AEP standard planning practices; prioritizes routine work to meet the demands of the company; assists with providing input to annual budget, capital forecasts, five-year plan, and improvement requisitions; participates in planning meetings covering scheduling, operations, and maintenance of equipment; assists in the preparation of basic cost estimates using established guidelines;

PROBLEM-SOLVING AND INITIATIVE: Seeks opportunity to work beyond routine assignments by solving problems of light complexity; actively seeks out information to increase technical knowledge in area of responsibility; applies technical knowledge in resolving basic problems encountered in assigned work; uses initiative in looking for opportunities to increase job knowledge/technical skills.

DECISION MAKING AND BUSINESS AWARENESS CHARACTERISTICS: Develops an understanding of AEP’s organizational structure and the specific role and responsibility of their individual business unit; develops a basic understanding of utility accounting and financing; demonstrates an attitude, ability and desire to listen to and satisfy both internal and external customers who use and depend on our work; participation in professional and business organizations is encouraged; develops decision-making skills under guidance of higher level employees; develops an understanding of the roles and responsibilities of the local organizational unit.

PHYSICAL DEMANDS:

1) Ability to climb ladders and work at various heights above the ground in performance of the work

2) Must be able to distinguish colors on a standard color blindness test

3) Must be able to lift and carry required test equipment and tools.

4) Ability to work outdoors and in confined spaces, and to switch station equipment energized up to 765kV using the appropriate Personal Protective Equipment

P&C Field Technologist:

ESSENTIAL JOB FUNCTIONS:

Test complex protection & control devices and equipment periodically and as required.

Calibrate complex protection & control devices and equipment on a pre-established schedule and as required.

Perform switching at all voltage levels under the direction of the proper Dispatching Authority.

Maintain test equipment in good working order.

Maintain accurate records, reports and drawings as required.

Operate a computer device to test, calibrate, and retrieve data from protection & control devices.

Assist in the installation, maintenance, and operation of all relays, power line carrier sets, station SCADA, and associated communications equipment or cables as assigned.

Troubleshoot and repair complex electromechanical relays.

Troubleshoot and repair microprocessor based relays at the card level, such as replacing power supplies, communications cards, I/O cards, etc.

Diagnose equipment failures, protection mis-operations and assist with corrective action to affect repair and prevent recurrence.

Ensure the circuitry, installation and operation of equipment is correct prior to placing equipment in service. Read electrical schematics and determine that the physical installation at the site is electrically equivalent to the schematic.

Record test readings and results and determine they are within acceptable specifications and thus the physical installation will perform as per the design.

Fault analysis: obtain oscillography data to determine if the protective devices operated as per their issued relay settings.

Leading a team in the installation, testing, and commissioning of new P&C systems for capital construction projects. Acting as the on-site technical lead and directing the activities of contract wireman and the activities of other P&C field personnel assigned to their project.

Lead a trip testing team with moderately complex protection & control systems.

MINIMUM REQUIREMENTS:

Education: Bachelor's degree in engineering in a program accredited by the Engineering Accreditation Commission of the Accreditation Board for Engineering and Technology (ABET) or a Bachelor's degree in engineering technology in a program accredited by the Technology Accreditation Commission of the Accreditation Board for Engineering and Technology (ABET).

Experience: Has typically acquired 2 or more years of related experience in work activities and projects requiring the application of engineering technology principles. Must successfully complete the Physical Abilities Test(PAT)

OTHER REQUIREMENTS:

1. Working knowledge of current, potential, closing and trip circuits.

2. Working knowledge of material such as cable, lugs, and wire as applied to protective relay and control circuits.

3. Working knowledge of assembly, anchoring, and interchangeability of the various switchboard panel-support and through systems.

4. Must have the ability to read, understand, and correct electrical prints and diagrams and the ability to use hand tools.

5. Must demonstrate the ability to perform duties in an alert, safe, and business-like manner and the ability to deal with customers and other employees in a courteous and professional manner.

6. Ability to interpret, analyze and transmit facts graphically, orally, and in writing clearly and precisely.

7. Must possess and maintain a valid state driver’s license and must meet all vehicle operation requirements as designated by federal and/or state law.

8. Considerable travel and overtime may be required to complete work assignments.

COMPETENCIES TECHNICAL PROFICIENCY : Demonstrates an intermediate level ability to perform with minimal guidance a variety of non-routine technical assignments of a complex nature. Exhibits ability to understand interrelationship between systems and component equipment in area of assignment.

LEADERSHIP AND GUIDANCE :Leads, facilitates, and coordinates work activities of others within the work group, team, department or other corporate entity as necessary to perform all routine engineering technology effort. Ensures all work activities are performed in accordance with the policies, practices, standards, and rules of the company.

PLANNING AND ORGANIZATION ABILITY :Organizes and conducts planning meetings covering scheduling, operations, and maintenance of equipment with applicable company and contract personnel. Review trends of material and equipment performance and initiate necessary corrective action.

PROBLEM-SOLVING AND INITIATIVE : Works independently in identifying and resolving complex problems. Seeks to broaden knowledge in areas of the company and industry which will complement acquired technical expertise.

COMMUNICATION AND INTERPERSONAL SKILLS : Develops, reviews or prepares technical reports clearly, concisely and effectively. Leads and facilitates meetings effectively. Functions as a team leader and member. Networks with peers inside and outside the AEP System. Identifies key stakeholders. Uses informal network to get things done.

DECISION MAKING AND BUSINESS AWARENESS CHARACTERISTICS : Uses diverse approaches to make decisions in the absence of a definite framework or where few precedents exist. Demonstrates the ability to handle conflicting interests related to approaches on projects or studies; also demonstrates the ability to analyze options and risks. Makes decisions which may affect the operations or results of the department and which may have some impact on the business unit. Exhibits an awareness of AEP’s competitive position and how business decisions impact their organizational unit. Understands the specific goals and objectives of their individual organizational unit and directly contributes to achieving them

PHYSICAL DEMANDS:

1) Ability to climb ladders and work at various heights above the ground in performance of the work

2) Must be able to distinguish colors on a standard color blindness test

3) Must be able to lift and carry required test equipment and tools.

4) Ability to work outdoors and in confined spaces, and to switch station equipment energized up to 765kV using the appropriate Personal Protective Equipment

P&C Field Technologist Senior:

ESSENTIAL JOB FUNCTIONS:

Develop plans and test complex protection & control devices and equipment periodically and as required.

Develop the test plans and calibrate complex protection & control devices and equipment on a pre-established schedule and as required.

Provide recommendations and perform switching at all voltage levels under the direction of the proper Dispatching Authority.

Maintain test equipment in good working order.

Maintain accurate records, reports and drawings as required.

Operate a computer device to test, calibrate, and retrieve data from protection & control devices.

Lead the installation, maintenance, and operation of all relays, power line carrier sets, station SCADA, and associated communications equipment or cables as assigned.

Demonstrate advanced knowledge in troubleshooting and repairing complex electromechanical relays at the system level.

Demonstrate advanced knowledge in troubleshooting and repairing microprocessor based relays at the system level.

Advanced diagnosis of equipment failures, protection mis-operations and determine corrective action to perform repairs and prevent recurrence.

Ensure the circuitry, installation and operation of advanced protection & control equipment is correct prior to placing equipment in service. Read electrical schematics and determine that the physical installation at the site is electrically equivalent to the schematic. Record test readings and results and determine they are within acceptable specifications and thus the physical installation will perform as per the design.

Advanced Fault analysis: Compile and analyze oscillography data at a system level to determine if the protective devices operated as per their issued relay settings.

Leading a team in the installation, testing, and commissioning of large complex P&C systems for capital construction projects. Acting as the on-site technical lead and directing the activities of contract wireman and the activities of other P&C field personnel assigned to their project.

Lead a trip testing team with testing complex EHV, Industrial and Power Plant protection & control systems.

MINIMUM REQUIREMENTS:

Education: Bachelor's degree in engineering in a program accredited by the Engineering Accreditation Commission of the Accreditation Board for Engineering and Technology (ABET) or a Bachelor's degree in engineering technology in a program accredited by the Technology Accreditation Commission of the Accreditation Board for Engineering and Technology (ABET).

Experience: Has typically acquired 6 or more years of related experience in work activities and projects requiring the application of engineering technology principles Must successfully complete the Physical Abilities Test(PAT)

OTHER REQUIREMENTS:

1. Working knowledge of current, potential, closing and trip circuits.

2. Working knowledge of material such as cable, lugs, and wire as applied to protective relay and control circuits.

3. Working knowledge of assembly, anchoring, and interchangeability of the various switchboard panel-supports and through systems.

4. Must have the ability to read, understand, and correct electrical prints and diagrams and the ability to use hand tools.

5. Must demonstrate the ability to perform duties in an alert, safe, and business-like manner and the ability to deal with customers and other employees in a courteous and professional manner.

6. Ability to interpret, analyze and transmit facts graphically, orally, and in writing clearly and precisely.

7. Considerable travel and overtime may be required to complete work assignments.

COMPETENCIES TECHNICAL PROFICIENCY :Exhibits journey to advanced level proficiency plus unique knowledge that allows effective participation in recommended courses of action, and the achievement of satisfactory solutions to advanced technical problems.

LEADERSHIP AND GUIDANCE :Leads project activity related to specific, unique, and/or highly specialized areas of engineering technology application.Leads, facilitates, and coordinates work activities of others within work group, team, department or other corporate entity as necessary, and assumes the role of project manager for assigned tasks. Coordinates and conducts training.

PLANNING AND ORGANIZATION ABILITY: Maintains required records to support assignments and prepares special reports for tests, equipment performance, projects and other reports as assigned.Plans work in accordance with AEP standard planning practices.Prioritizes routine work to meet the demands of the company. Assists with providing input to annual budget, capital forecasts, five-year plan, and improvement requisitions.Participates in planning meetings covering scheduling, operations, and maintenance of equipment. Assists in the preparation of basic cost estimates using established guidelines.

PROBLEM-SOLVING AND INITIATIVE : Reviews planned work of others when assigned.Organizes and leads special projects and task forces as assigned.

COMMUNICATION AND INTERPERSONAL SKILLS : Projects credibility and competence on technical issues and has highly developed presentation skills. Networks throughout AEP, other companies, professional organizations, and regulatory agencies.

DECISION MAKING AND BUSINESS AWARENESS CHARACTERISTICS : Possesses the knowledge to make technical decisions based on calculated risks with little or no management review. Understands how technical strategies and decisions impact the relationship with customers. Demonstrates the ability to make decisions affecting long-range plans & goals based on analysis of uncertain input & outcomes. Makes decisions where differences of opinion are likely to exist. Provides input into decisions which have an impact across organizational boundaries.

PHYSICAL DEMANDS:

1) Ability to climb ladders and work at various heights above the ground in performance of the work

2) Must be able to distinguish colors on a standard color blindness test

3) Must be able to lift and carry required test equipment and tools.

4) Ability to work outdoors and in confined spaces, and to switch station equipment energized up to 765kV using the appropriate Personal Protective Equipment

Compensation Range:

$29.63 per hour- $40.90 per hour

Compensation Data

Compensation Grade:

SP20-005

Compensation Range:

$29.64-37.05 USD

The Physical Demand Level for this job is: L – Light Work: Exerting up to 20 pounds of force occasionally and/or 10 to 12 pounds of force frequently, and/or greater than negligible up to 5-6 pounds of force constantly to move objects. Physical demand requirements are in excess of those for sedentary work. Even though the weight lifted may be only a negligible amount, a job should be rated Light Work: (1) When it requires walking or standing to a significant degree; or (2) when it requires sitting most of the time, but entails pushing and/or pulling of arm or leg c ontrols; and/or (3) when the job requires working at a production rate pace entailing the constant pushing and/or pulling of materials even though the weight of those materials is negligible. NOTE: The constant stress and strain of maintaining a production rate pace, especially in an industrial setting, can be and is physically demanding of a worker even though the amount of force exerted is negligible

Hear about it first! Get job alerts by email. Log in to your Candidate Home Account today! If you don't have an account, you can create one.

It is hereby reaffirmed that it is the policy of American Electric Power (AEP) to provide Equal Employment Opportunity in all respects of the employer-employee relationship including recruiting, hiring, upgrading and promotion, conditions and privileges of employment, company sponsored training programs, educational assistance, social and recreational programs, compensation, benefits, transfers, discipline, layoffs and termination of employment to all employees and applicants without discrimination because of race, color, religion, sex (including pregnancy, gender identity, and sexual orientation), national origin, age, veteran or military status, disability, genetic information, or any other basis prohibited by applicable law. When required by law, we might record certain information or applicants for employment may be invited to voluntarily disclose protected characteristics.